VK4RBX-C Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK4RBX-C. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPU-c*	Mem%*	RPTxT*
1788600602	33 degC	15 Pct	10 Min
1788598802	35 degC	15 Pct	1 Min
1788597002	34 degC	15 Pct	1 Min
1788595202	36 degC	15 Pct	1 Min
1788593402	35 degC	15 Pct	1 Min
1788591602	35 degC	15 Pct	1 Min
1788589802	35 degC	15 Pct	1 Min
1788588002	37 degC	15 Pct	1 Min
1788586201	35 degC	15 Pct	1 Min
1788584402	35 degC	15 Pct	0 Min
1788582601	36 degC	15 Pct	0 Min
1788580802	34 degC	15 Pct	0 Min
1788579002	35 degC	15 Pct	0 Min
1788577202	34 degC	15 Pct	0 Min
1788575404	34 degC	15 Pct	0 Min
1788573602	34 degC	15 Pct	0 Min
1788571802	33 degC	15 Pct	0 Min
1788570002	34 degC	15 Pct	0 Min
1788568202	35 degC	15 Pct	0 Min
1788566402	33 degC	15 Pct	0 Min
1788564602	33 degC	15 Pct	0 Min
1788562802	33 degC	15 Pct	0 Min
1788561002	34 degC	15 Pct	0 Min
1788559202	33 degC	15 Pct	0 Min
1788557401	33 degC	15 Pct	0 Min

*Used Equation Coefficients:

Tx5m: 0, 1, 0

Rx5m: 0, 1, 0

CPU-c: 0, 1, 20

Mem%: 0, 1, 0

RPTxT: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)