BV8SI-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV8SI-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/10m*	RxPkts/1h*	RxPkts/24h*	DiGi*
1777045925	20 C	143 p	143 p	143 p	270751 p
1777044726	21 C	143 p	143 p	143 p	270731 p
1777043526	21 C	143 p	143 p	143 p	270701 p
1777042326	22 C	143 p	143 p	143 p	270686 p
1777041126	22 C	143 p	143 p	143 p	270676 p
1777039927	21 C	143 p	143 p	143 p	270662 p
1777037527	22 C	143 p	143 p	143 p	270613 p
1777036326	21 C	143 p	143 p	143 p	270587 p
1777035127	21 C	143 p	143 p	143 p	270535 p
1777033926	22 C	143 p	143 p	143 p	270485 p
1777032726	22 C	143 p	143 p	143 p	270463 p
1777031527	23 C	143 p	143 p	143 p	270447 p
1777030326	22 C	143 p	143 p	143 p	270423 p
1777029127	23 C	143 p	143 p	143 p	270405 p
1777027927	23 C	143 p	143 p	143 p	270376 p
1777026727	24 C	143 p	143 p	143 p	270335 p
1777025527	23 C	143 p	143 p	143 p	270280 p
1777024327	23 C	143 p	143 p	143 p	270219 p
1777023127	23 C	143 p	143 p	143 p	270185 p
1777021928	24 C	143 p	143 p	143 p	270165 p
1777020726	26 C	143 p	143 p	143 p	270130 p
1777019526	25 C	143 p	143 p	143 p	270105 p
1777018327	26 C	143 p	143 p	143 p	270060 p
1777017127	26 C	143 p	143 p	143 p	270022 p
1777015927	25 C	143 p	143 p	143 p	269988 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/10m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)