SP8JCF Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP8JCF. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1753552300	12.23 Volt	150 Pkt	70 Pkt	65 Pcnt
1753552295	12.23 Volt	150 Pkt	70 Pkt	65 Pcnt
1753551995	12.23 Volt	150 Pkt	70 Pkt	65 Pcnt
1753551695	12.23 Volt	140 Pkt	70 Pkt	64 Pcnt
1753551395	12.23 Volt	130 Pkt	60 Pkt	61 Pcnt
1753551102	12.23 Volt	120 Pkt	60 Pkt	61 Pcnt
1753551095	12.23 Volt	120 Pkt	60 Pkt	61 Pcnt
1753550795	12.23 Volt	110 Pkt	50 Pkt	60 Pcnt
1753550500	12.23 Volt	100 Pkt	40 Pkt	59 Pcnt
1753550495	12.23 Volt	100 Pkt	40 Pkt	59 Pcnt
1753550195	12.23 Volt	100 Pkt	50 Pkt	62 Pcnt
1753549895	12.23 Volt	100 Pkt	40 Pkt	57 Pcnt
1753549595	12.23 Volt	90 Pkt	40 Pkt	53 Pcnt
1753549300	12.23 Volt	100 Pkt	40 Pkt	50 Pcnt
1753549295	12.23 Volt	100 Pkt	40 Pkt	50 Pcnt
1753548995	12.23 Volt	100 Pkt	50 Pkt	51 Pcnt
1753548720	12.23 Volt	100 Pkt	40 Pkt	50 Pcnt
1753548720	12.23 Volt	100 Pkt	40 Pkt	50 Pcnt
1753548395	12.23 Volt	100 Pkt	40 Pkt	48 Pcnt
1753548100	12.23 Volt	100 Pkt	40 Pkt	50 Pcnt
1753548095	12.23 Volt	100 Pkt	40 Pkt	50 Pcnt
1753547795	12.23 Volt	100 Pkt	40 Pkt	50 Pcnt
1753547500	12.23 Volt	100 Pkt	40 Pkt	48 Pcnt
1753547495	12.23 Volt	100 Pkt	40 Pkt	48 Pcnt
1753547195	12.23 Volt	100 Pkt	50 Pkt	45 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)