HS3PIK-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS3PIK-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	WiFi*	BaudRate*
1777593324	17 Pkt	43 dB	19200 bps
1777592724	10 Pkt	42 dB	19200 bps
1777592124	14 Pkt	41 dB	19200 bps
1777591524	20 Pkt	44 dB	19200 bps
1777590924	14 Pkt	43 dB	19200 bps
1777590324	14 Pkt	44 dB	19200 bps
1777589724	17 Pkt	44 dB	19200 bps
1777589124	10 Pkt	46 dB	19200 bps
1777588524	14 Pkt	44 dB	19200 bps
1777587924	14 Pkt	43 dB	19200 bps
1777587324	20 Pkt	44 dB	19200 bps
1777586724	14 Pkt	46 dB	19200 bps
1777586124	11 Pkt	44 dB	19200 bps
1777585524	16 Pkt	43 dB	19200 bps
1777584924	14 Pkt	44 dB	19200 bps
1777584324	14 Pkt	44 dB	19200 bps
1777583724	20 Pkt	46 dB	19200 bps
1777583124	14 Pkt	44 dB	19200 bps
1777582524	10 Pkt	42 dB	19200 bps
1777581924	17 Pkt	44 dB	19200 bps
1777581324	14 Pkt	46 dB	19200 bps
1777580724	14 Pkt	40 dB	19200 bps
1777580124	14 Pkt	41 dB	19200 bps
1777579524	20 Pkt	44 dB	19200 bps
1777578929	11 Pkt	42 dB	19200 bps

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

WiFi: 0, 1, 100

BaudRate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)