KN4YDP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KN4YDP-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1773447673	11.7 Volts	17.66 Deg.C
1773447553	11.73 Volts	17.66 Deg.C
1773447492	11.7 Volts	17.66 Deg.C
1773447433	11.7 Volts	17.66 Deg.C
1773447372	11.7 Volts	18.15 Deg.C
1773446654	11.73 Volts	19.13 Deg.C
1773446593	11.7 Volts	19.13 Deg.C
1773446533	11.73 Volts	19.13 Deg.C
1773446473	11.73 Volts	19.13 Deg.C
1773446233	11.73 Volts	19.62 Deg.C
1773446174	11.7 Volts	19.62 Deg.C
1773446053	11.73 Volts	19.62 Deg.C
1773445933	11.73 Volts	19.62 Deg.C
1773445872	11.73 Volts	19.13 Deg.C
1773445753	11.76 Volts	19.62 Deg.C
1773445692	11.73 Volts	19.62 Deg.C
1773445633	11.76 Volts	19.62 Deg.C
1773445572	11.76 Volts	19.62 Deg.C
1773445394	11.76 Volts	20.11 Deg.C
1773445333	11.76 Volts	20.11 Deg.C
1773445033	11.76 Volts	20.11 Deg.C
1773444972	11.79 Volts	20.11 Deg.C
1773444732	11.76 Volts	20.59 Deg.C
1773444448	11.73 Volts	22.55 Deg.C
1773444312	11.85 Volts	23.04 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.02933, 0

Temp: 0, 0.48876, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)