SA3VCC-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SA3VCC-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	VBat*	CpuTemp*	CpuHum*	Lux*
1785311255	4.33 V	56.3 C	32.2 %	24551 lx
1785309981	4.39 V	54.6 C	32.4 %	31777 lx
1785308708	4.39 V	51.8 C	33.2 %	28811 lx
1785307434	4.48 V	47.3 C	34.5 %	9925 lx
1785306161	4.45 V	42.5 C	35.6 %	13241 lx
1785302342	4.33 V	17.8 C	47.2 %	2875 lx
1785301068	4.33 V	16.3 C	47.1 %	2637 lx
1785299795	4.32 V	14.8 C	47.2 %	2344 lx
1785298522	4.32 V	13.9 C	47.3 %	2133 lx
1785297249	4.32 V	13.8 C	46.3 %	2047 lx
1785295976	4.32 V	11.5 C	47.5 %	1916 lx
1785294703	4.32 V	10.4 C	48 %	974 lx
1785293430	4.32 V	9.9 C	48.5 %	610 lx
1785292155	4.32 V	9.8 C	48.8 %	272 lx
1785289606	4.32 V	10.1 C	49.2 %	16 lx
1785288332	4.31 V	10.3 C	49.5 %	2 lx
1785285786	4.32 V	11.4 C	49.9 %	0 lx
1785283240	4.32 V	13.2 C	50.1 %	0 lx
1785281967	4.32 V	14.2 C	49.8 %	0 lx
1785280694	4.32 V	15 C	49.5 %	0 lx
1785279421	4.32 V	15 C	49.8 %	0 lx
1785278148	4.32 V	14.9 C	50.3 %	0 lx
1785276874	4.32 V	15.4 C	50.4 %	0 lx
1785275601	4.32 V	16.2 C	50.2 %	0 lx
1785273055	4.32 V	17 C	50.2 %	0 lx

*Used Equation Coefficients:

VBat: 0, 0.01, 2.5

Bat: 0, 1, 0

CpuTemp: 0, 0.1, 0

CpuHum: 0, 0.1, 0

Lux: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)