WB6CDF Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WB6CDF. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1773026379	13.45 Volts	-459.67 Deg.F
1773026334	14.33 Volts	-459.67 Deg.F
1773026297	13.3 Volts	-459.67 Deg.F
1773026258	13.39 Volts	-459.67 Deg.F
1773026179	14.21 Volts	-459.67 Deg.F
1773026167	13.54 Volts	-459.67 Deg.F
1773026150	13.51 Volts	-459.67 Deg.F
1773026141	13.57 Volts	-459.67 Deg.F
1773026068	13.57 Volts	-459.67 Deg.F
1773026060	14.24 Volts	-459.67 Deg.F
1773026043	14.27 Volts	-459.67 Deg.F
1773026000	13.57 Volts	-459.67 Deg.F
1773025933	14.39 Volts	-459.67 Deg.F
1773025888	13.45 Volts	-459.67 Deg.F
1773009673	13.54 Volts	-459.67 Deg.F
1773009610	13.39 Volts	-459.67 Deg.F
1773009602	13.48 Volts	-459.67 Deg.F
1773009598	13.86 Volts	-459.67 Deg.F
1773009478	13.54 Volts	-459.67 Deg.F
1773009461	13.45 Volts	-459.67 Deg.F
1773009443	14.27 Volts	-459.67 Deg.F
1773009428	13.54 Volts	-459.67 Deg.F
1773009413	13.54 Volts	-459.67 Deg.F
1773009406	13.51 Volts	-459.67 Deg.F
1773008900	13.39 Volts	-459.67 Deg.F

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.879, -459.67

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)