DF7ER-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DF7ER-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Pres*	Humi*
1776669802	6 deg.C	1007 mbar	92 Percen
1776669502	6.5 deg.C	1007 mbar	91 Percen
1776669202	6 deg.C	1007 mbar	91 Percen
1776668902	6.5 deg.C	1007 mbar	91 Percen
1776668602	6 deg.C	1007 mbar	93 Percen
1776668302	6.5 deg.C	1007 mbar	92 Percen
1776668002	5.5 deg.C	1007 mbar	94 Percen
1776667702	5.5 deg.C	1007 mbar	94 Percen
1776667402	6.5 deg.C	1007 mbar	91 Percen
1776667102	5.5 deg.C	1007 mbar	94 Percen
1776666802	6 deg.C	1007 mbar	94 Percen
1776666502	5.5 deg.C	1007 mbar	94 Percen
1776666202	6 deg.C	1007 mbar	93 Percen
1776665902	6 deg.C	1007 mbar	94 Percen
1776665602	6.5 deg.C	1007 mbar	92 Percen
1776665302	6 deg.C	1007 mbar	93 Percen
1776665002	6.5 deg.C	1007 mbar	94 Percen
1776664703	6.5 deg.C	1007 mbar	93 Percen
1776664402	6 deg.C	1007 mbar	95 Percen
1776664102	7 deg.C	1007 mbar	91 Percen
1776663802	7 deg.C	1006 mbar	93 Percen
1776663502	6.5 deg.C	1006 mbar	93 Percen
1776663202	6.5 deg.C	1006 mbar	94 Percen
1776662902	6 deg.C	1006 mbar	95 Percen
1776662602	6.5 deg.C	1006 mbar	93 Percen

*Used Equation Coefficients:

Temp: 0, 0.5, -40

Pres: 0, 1, 850

Humi: 0, 0.5, 0

xxx: 0, 1, 0

yyy: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)