DB0PIB Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0PIB. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vfm*	Vbuf*	Tbat*
1776655839	13.4 V	13.5 V	8.5 C
1776655539	13.4 V	13.5 V	8.5 C
1776655239	13.4 V	13.5 V	8.5 C
1776654939	13.4 V	13.5 V	8 C
1776654639	13.4 V	13.4 V	8 C
1776654339	13.4 V	13.4 V	8 C
1776654039	13.4 V	13.5 V	8 C
1776653739	13.4 V	13.5 V	8 C
1776653439	13.4 V	13.5 V	8 C
1776653139	13.4 V	13.5 V	8 C
1776652839	13.4 V	13.5 V	8 C
1776652539	13.4 V	13.5 V	8 C
1776652239	13.4 V	13.5 V	8 C
1776651939	13.4 V	13.5 V	8 C
1776651639	13.4 V	13.5 V	8 C
1776651339	13.4 V	13.5 V	8 C
1776651039	13.4 V	13.5 V	8 C
1776650739	13.4 V	13.5 V	8.5 C
1776650440	13.4 V	13.5 V	8.5 C
1776650139	13.4 V	13.5 V	8.5 C
1776649839	13.4 V	13.5 V	8.5 C
1776649539	13.4 V	13.5 V	8.5 C
1776649239	13.4 V	13.5 V	8.5 C
1776648939	13.4 V	13.5 V	8.5 C
1776648639	13.4 V	13.5 V	8.5 C

*Used Equation Coefficients:

Vfm: 0, 0.1, 0

Vbuf: 0, 0.1, 0

Isol: 0, 0.1953, -24.8031

Ievs: 0, 0.1953, -24.8031

Tbat: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)