DG3NAD-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG3NAD-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1772631465	21.8 deg C	65.6 %	1025.7 hPa
1772630565	22.4 deg C	64.9 %	1024.7 hPa
1772629665	22.6 deg C	64.7 %	1024.7 hPa
1772628764	22.7 deg C	64.8 %	1025.4 hPa
1772627866	23.4 deg C	63.5 %	1024 hPa
1772626964	24 deg C	62.2 %	1025.2 hPa
1772626064	24.1 deg C	61.5 %	1026.1 hPa
1772625166	24.5 deg C	60.4 %	1025 hPa
1772624264	24.2 deg C	60.1 %	1025.4 hPa
1772623364	23.8 deg C	60.2 %	1025.4 hPa
1772622464	23.8 deg C	59.7 %	1024.5 hPa
1772621564	23.7 deg C	59 %	1026.9 hPa
1772620663	23.1 deg C	59 %	1025.7 hPa
1772619763	22.5 deg C	58.9 %	1026.9 hPa
1772618879	21.3 deg C	59.5 %	1025.7 hPa
1772617963	20 deg C	60.6 %	1028.9 hPa
1772617063	18.8 deg C	61.3 %	1027 hPa
1772616163	17.8 deg C	61.8 %	1027 hPa
1772615263	16.9 deg C	62.3 %	1027.4 hPa
1772614363	16.4 deg C	62.3 %	1027.2 hPa
1772613463	15.7 deg C	62.2 %	1026.4 hPa
1772612562	14.9 deg C	62.6 %	1025.9 hPa
1772611662	13.5 deg C	63.8 %	1027.2 hPa
1772610762	12.2 deg C	64.8 %	1027.5 hPa
1772609862	10.3 deg C	66.7 %	1027.9 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)