HP2PCE-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HP2PCE-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1776635759	13.65 Volt	240 Pkt	110 Pkt	63 Pcnt
1776635037	13.65 Volt	250 Pkt	110 Pkt	64 Pcnt
1776634316	13.65 Volt	250 Pkt	120 Pkt	67 Pcnt
1776633596	13.65 Volt	260 Pkt	120 Pkt	69 Pcnt
1776632875	13.65 Volt	250 Pkt	120 Pkt	69 Pcnt
1776632154	13.65 Volt	250 Pkt	110 Pkt	70 Pcnt
1776631436	13.65 Volt	240 Pkt	120 Pkt	68 Pcnt
1776630713	13.65 Volt	250 Pkt	110 Pkt	69 Pcnt
1776629992	13.65 Volt	240 Pkt	100 Pkt	68 Pcnt
1776629272	13.65 Volt	240 Pkt	100 Pkt	68 Pcnt
1776627830	13.65 Volt	250 Pkt	110 Pkt	66 Pcnt
1776627110	13.65 Volt	240 Pkt	110 Pkt	66 Pcnt
1776626389	13.65 Volt	250 Pkt	110 Pkt	67 Pcnt
1776625668	13.65 Volt	250 Pkt	120 Pkt	67 Pcnt
1776624949	13.65 Volt	250 Pkt	120 Pkt	67 Pcnt
1776624227	13.65 Volt	240 Pkt	120 Pkt	67 Pcnt
1776623506	13.65 Volt	250 Pkt	130 Pkt	69 Pcnt
1776622786	13.65 Volt	240 Pkt	120 Pkt	70 Pcnt
1776622065	13.65 Volt	230 Pkt	120 Pkt	71 Pcnt
1776620623	13.65 Volt	230 Pkt	120 Pkt	76 Pcnt
1776619903	13.65 Volt	230 Pkt	110 Pkt	74 Pcnt
1776619182	13.65 Volt	230 Pkt	120 Pkt	74 Pcnt
1776618464	13.65 Volt	220 Pkt	110 Pkt	73 Pcnt
1776617741	13.65 Volt	200 Pkt	110 Pkt	71 Pcnt
1776617020	13.65 Volt	200 Pkt	110 Pkt	70 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)