ED1ZAW-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED1ZAW-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Volt.*	Rx/h*	Temp*	Efic*
1788571157	13.95 V.	240 Pkt	21 C	74 %
1788571154	13.95 V.	240 Pkt	21 C	74 %
1788570555	13.95 V.	260 Pkt	21 C	74 %
1788570434	13.95 V.	260 Pkt	21 C	74 %
1788569958	13.88 V.	250 Pkt	21 C	74 %
1788569714	13.95 V.	250 Pkt	21 C	74 %
1788569355	13.95 V.	250 Pkt	21 C	74 %
1788568994	13.95 V.	230 Pkt	21 C	74 %
1788568755	13.95 V.	220 Pkt	21 C	74 %
1788568274	13.95 V.	220 Pkt	21 C	74 %
1788568155	13.95 V.	220 Pkt	21 C	74 %
1788567555	13.88 V.	200 Pkt	21 C	74 %
1788567554	13.88 V.	200 Pkt	21 C	74 %
1788566955	13.95 V.	190 Pkt	20.5 C	74 %
1788566834	13.95 V.	190 Pkt	20.5 C	74 %
1788566355	13.95 V.	190 Pkt	20.5 C	74 %
1788566114	13.95 V.	180 Pkt	20.5 C	74 %
1788565755	13.95 V.	200 Pkt	20.5 C	74 %
1788565394	13.95 V.	200 Pkt	20.5 C	74 %
1788565155	13.95 V.	200 Pkt	20.5 C	74 %
1788564674	13.95 V.	210 Pkt	21 C	74 %
1788564555	13.88 V.	220 Pkt	21 C	74 %
1788563955	13.88 V.	230 Pkt	21 C	74 %
1788563954	13.88 V.	230 Pkt	21 C	74 %
1788563355	13.95 V.	250 Pkt	21.5 C	74 %

*Used Equation Coefficients:

Volt.: 0, 0.075, 0

Rx/h: 0, 10, 0

Digi/h: 0, 10, 0

Temp: 0, 0.5, -64

Efic: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)