UR7D-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object UR7D-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1784702460	13.8 Volt	120 Pkt	90 Pkt	73 Pcnt
1784684440	13.8 Volt	120 Pkt	90 Pkt	89 Pcnt
1784678434	13.8 Volt	130 Pkt	110 Pkt	76 Pcnt
1784660417	13.73 Volt	130 Pkt	100 Pkt	77 Pcnt
1784654412	13.73 Volt	140 Pkt	110 Pkt	75 Pcnt
1784648407	13.73 Volt	140 Pkt	110 Pkt	81 Pcnt
1784642400	13.73 Volt	140 Pkt	110 Pkt	80 Pcnt
1784636394	13.73 Volt	130 Pkt	110 Pkt	84 Pcnt
1784630388	13.73 Volt	130 Pkt	100 Pkt	80 Pcnt
1784618377	13.8 Volt	130 Pkt	100 Pkt	77 Pcnt
1784612371	13.8 Volt	130 Pkt	110 Pkt	85 Pcnt
1784600361	13.8 Volt	130 Pkt	110 Pkt	82 Pcnt
1784594355	13.8 Volt	130 Pkt	110 Pkt	82 Pcnt
1784588348	13.8 Volt	140 Pkt	110 Pkt	71 Pcnt
1784582342	13.73 Volt	130 Pkt	100 Pkt	92 Pcnt
1784576336	13.73 Volt	130 Pkt	100 Pkt	93 Pcnt
1784558320	13.73 Volt	140 Pkt	110 Pkt	85 Pcnt
1784546310	13.73 Volt	140 Pkt	110 Pkt	82 Pcnt
1784540303	13.8 Volt	140 Pkt	100 Pkt	91 Pcnt
1784528291	13.8 Volt	130 Pkt	100 Pkt	89 Pcnt
1784522286	13.8 Volt	160 Pkt	120 Pkt	64 Pcnt
1784516279	13.8 Volt	150 Pkt	110 Pkt	80 Pcnt
1784510274	13.8 Volt	120 Pkt	100 Pkt	84 Pcnt
1784504277	13.8 Volt	120 Pkt	100 Pkt	81 Pcnt
1784498262	13.8 Volt	140 Pkt	100 Pkt	86 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)