OE1KDA-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE1KDA-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	eCO2*	Temp.out*
1788594906	0 C deg	706 ppm	0 C deg
1788593090	0 C deg	706 ppm	0 C deg
1788591289	0 C deg	785 ppm	0 C deg
1788589464	0 C deg	900 ppm	0 C deg
1788582217	0 C deg	1487 ppm	0 C deg
1788567691	0 C deg	1524 ppm	0 C deg
1788560418	0 C deg	915 ppm	0 C deg
1788558604	0 C deg	905 ppm	0 C deg
1788556786	0 C deg	889 ppm	0 C deg
1788554975	0 C deg	889 ppm	0 C deg
1788553160	0 C deg	905 ppm	0 C deg
1788551344	0 C deg	915 ppm	0 C deg
1788549544	0 C deg	874 ppm	0 C deg
1788547710	0 C deg	776 ppm	0 C deg
1788545898	0 C deg	692 ppm	0 C deg
1788544083	0 C deg	519 ppm	0 C deg
1788542266	0 C deg	427 ppm	0 C deg
1788540454	0 C deg	427 ppm	0 C deg
1788538638	0 C deg	486 ppm	0 C deg
1788536825	0 C deg	575 ppm	0 C deg
1788535008	0 C deg	629 ppm	0 C deg
1788533208	0 C deg	719 ppm	0 C deg
1788531378	0 C deg	872 ppm	0 C deg
1788529562	0 C deg	905 ppm	0 C deg
1788527754	0 C deg	900 ppm	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

eCO2: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)