This is the latest recevied telemetry packets stored in our database for station/object ED7YAX-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
VAPRS*
VREPE*
Carga*
Trepe*
Taprs*
1780382963
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780382663
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780382363
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780382063
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780381763
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780334445
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780334145
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780333845
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780332971
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780332671
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780332371
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780332071
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780331771
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780331309
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780331009
14.58 Volt
0 Volt
-2496 mA
-64 C
0 C
1780330593
14.65 Volt
0 Volt
-2496 mA
-64 C
0 C
1780330293
14.65 Volt
0 Volt
-2496 mA
-64 C
0 C
1780329994
14.65 Volt
0 Volt
-2496 mA
-64 C
0 C
*Used Equation Coefficients:
VAPRS: 0, 0.074, 0
VREPE: 0, 0.074, 0
Carga: 0, 19.5, -2496
Trepe: 0, 0.5, -64
Taprs: 0, 0.5, -64
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)