VK4KLL-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK4KLL-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BATT1*	T1 PL60*	T2 INV*	Rx1h*
1784740505	12.71 Volt	63.5 C	24 C	130 Pkt
1784738405	12.71 Volt	63.5 C	24 C	120 Pkt
1784736304	12.71 Volt	63.5 C	24 C	120 Pkt
1784733604	12.71 Volt	63.5 C	24 C	130 Pkt
1784729104	12.71 Volt	63.5 C	24 C	110 Pkt
1784728204	12.71 Volt	63.5 C	24 C	110 Pkt
1784727904	12.71 Volt	63.5 C	24 C	100 Pkt
1784727904	12.71 Volt	63.5 C	24 C	100 Pkt
1784727604	12.71 Volt	63.5 C	24 C	110 Pkt
1784727304	12.71 Volt	63.5 C	24 C	100 Pkt
1784727004	12.71 Volt	63.5 C	24 C	100 Pkt
1784726704	12.71 Volt	63.5 C	24 C	100 Pkt
1784726404	12.71 Volt	63.5 C	24 C	120 Pkt
1784726104	12.71 Volt	63.5 C	24 C	110 Pkt
1784725804	12.71 Volt	63.5 C	24 C	110 Pkt
1784725504	12.71 Volt	63.5 C	24 C	100 Pkt
1784725204	12.71 Volt	63.5 C	24 C	100 Pkt
1784724904	12.71 Volt	63.5 C	24 C	110 Pkt
1784724604	12.71 Volt	63.5 C	24 C	120 Pkt
1784724304	12.71 Volt	63.5 C	24.5 C	120 Pkt
1784724004	12.71 Volt	63.5 C	24.5 C	130 Pkt
1784723704	12.71 Volt	63.5 C	24.5 C	130 Pkt
1784723404	12.71 Volt	63.5 C	24.5 C	130 Pkt
1784723104	12.71 Volt	63.5 C	24.5 C	110 Pkt
1784722804	12.71 Volt	63.5 C	24.5 C	120 Pkt

*Used Equation Coefficients:

BATT1: 0, 0.079, -0.8

T1 PL60: 0, 0.5, -64

T2 INV: 0, 0.5, -64

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)