IQ3TS-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IQ3TS-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10m*	Rx1h*	Volt*
1788566375	98 Pkt	680 Pkt	14.38 Volt
1788566075	109 Pkt	700 Pkt	14.38 Volt
1788565775	89 Pkt	700 Pkt	14.38 Volt
1788565475	93 Pkt	700 Pkt	14.38 Volt
1788565175	113 Pkt	710 Pkt	14.38 Volt
1788564875	111 Pkt	720 Pkt	14.38 Volt
1788564575	101 Pkt	760 Pkt	14.38 Volt
1788564275	110 Pkt	780 Pkt	14.38 Volt
1788563975	114 Pkt	820 Pkt	14.38 Volt
1788563675	103 Pkt	790 Pkt	14.38 Volt
1788563375	110 Pkt	810 Pkt	14.38 Volt
1788563075	111 Pkt	810 Pkt	14.38 Volt
1788562775	116 Pkt	830 Pkt	14.38 Volt
1788562475	109 Pkt	850 Pkt	14.38 Volt
1788562175	98 Pkt	850 Pkt	14.38 Volt
1788561875	119 Pkt	860 Pkt	14.38 Volt
1788561575	168 Pkt	890 Pkt	14.38 Volt
1788561275	166 Pkt	910 Pkt	14.38 Volt
1788560975	159 Pkt	900 Pkt	14.38 Volt
1788560675	121 Pkt	930 Pkt	14.38 Volt
1788560375	98 Pkt	920 Pkt	14.38 Volt
1788560075	108 Pkt	920 Pkt	14.38 Volt
1788559775	142 Pkt	890 Pkt	14.38 Volt
1788559475	146 Pkt	880 Pkt	14.38 Volt
1788559175	118 Pkt	830 Pkt	14.38 Volt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Dg10m: 0, 1, 0

DgR: 0, 0.001, 0

Volt: 0, 0.079, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)