This is the latest recevied telemetry packets stored in our database for station/object DB0TIT-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Vin*
Rx1h*
Dg1h*
Eff1h*
Effto*
1776672569
13.9 Volt
280 Pkt
80 Pkt
55 Pcnt
0 None
1776668969
13.9 Volt
290 Pkt
90 Pkt
55 Pcnt
0 None
1776665369
13.9 Volt
420 Pkt
120 Pkt
55 Pcnt
0 None
1776661769
13.9 Volt
550 Pkt
160 Pkt
55 Pcnt
0 None
1776658169
13.9 Volt
430 Pkt
110 Pkt
55 Pcnt
0 None
1776654570
13.9 Volt
360 Pkt
110 Pkt
55 Pcnt
0 None
1776650970
13.9 Volt
290 Pkt
80 Pkt
55 Pcnt
0 None
1776647370
13.9 Volt
270 Pkt
80 Pkt
55 Pcnt
0 None
1776643770
13.9 Volt
320 Pkt
90 Pkt
55 Pcnt
0 None
1776640170
13.9 Volt
340 Pkt
70 Pkt
55 Pcnt
0 None
1776636571
13.9 Volt
380 Pkt
110 Pkt
55 Pcnt
0 None
1776632971
13.9 Volt
420 Pkt
140 Pkt
55 Pcnt
0 None
1776629371
13.9 Volt
500 Pkt
150 Pkt
55 Pcnt
0 None
1776625771
13.9 Volt
500 Pkt
170 Pkt
55 Pcnt
0 None
1776622171
13.9 Volt
400 Pkt
120 Pkt
55 Pcnt
0 None
1776618572
13.9 Volt
320 Pkt
70 Pkt
55 Pcnt
0 None
1776614972
13.9 Volt
460 Pkt
120 Pkt
55 Pcnt
0 None
*Used Equation Coefficients:
Vin: 0, 0.079, 0
Rx1h: 0, 10, 0
Dg1h: 0, 10, 0
Eff1h: 0, 1, 0
Effto: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)