N0MPM-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N0MPM-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1776697230	13.66 Volt	100 Pcnt	18 C
1776696930	13.66 Volt	100 Pcnt	18 C
1776696630	13.66 Volt	100 Pcnt	18 C
1776696330	13.66 Volt	100 Pcnt	18 C
1776696031	13.66 Volt	100 Pcnt	18 C
1776695731	13.59 Volt	100 Pcnt	18 C
1776695431	13.66 Volt	100 Pcnt	18 C
1776695131	13.66 Volt	100 Pcnt	18 C
1776694831	13.66 Volt	100 Pcnt	18 C
1776694531	13.66 Volt	100 Pcnt	18 C
1776694231	13.66 Volt	100 Pcnt	18 C
1776693931	13.66 Volt	100 Pcnt	18 C
1776693631	13.66 Volt	100 Pcnt	18 C
1776693331	13.66 Volt	100 Pcnt	18 C
1776693031	13.66 Volt	100 Pcnt	18 C
1776692731	13.66 Volt	100 Pcnt	18 C
1776692431	13.66 Volt	100 Pcnt	18 C
1776692131	13.66 Volt	100 Pcnt	18 C
1776691831	13.66 Volt	100 Pcnt	18 C
1776691531	13.66 Volt	100 Pcnt	18 C
1776691231	13.66 Volt	100 Pcnt	18 C
1776690931	13.66 Volt	100 Pcnt	18 C
1776690631	13.66 Volt	100 Pcnt	18 C
1776690331	13.66 Volt	100 Pcnt	18 C
1776690031	13.66 Volt	100 Pcnt	18 C

*Used Equation Coefficients:

Vin: 0, 0.07188, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)