N3XKU-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N3XKU-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1788573136	13.35 Volt	400 Pkt	84 Pcnt
1788571335	13.11 Volt	360 Pkt	78 Pcnt
1788569533	13.27 Volt	370 Pkt	77 Pcnt
1788567731	13.19 Volt	300 Pkt	76 Pcnt
1788565930	13.43 Volt	220 Pkt	77 Pcnt
1788564128	13.27 Volt	220 Pkt	76 Pcnt
1788562326	13.35 Volt	220 Pkt	77 Pcnt
1788560524	13.19 Volt	220 Pkt	78 Pcnt
1788558723	13.27 Volt	230 Pkt	79 Pcnt
1788556921	12.96 Volt	200 Pkt	79 Pcnt
1788555119	12.96 Volt	140 Pkt	81 Pcnt
1788553318	13.11 Volt	180 Pkt	76 Pcnt
1788551516	12.96 Volt	230 Pkt	76 Pcnt
1788549714	13.19 Volt	200 Pkt	78 Pcnt
1788547912	13.11 Volt	150 Pkt	76 Pcnt
1788546111	13.11 Volt	150 Pkt	78 Pcnt
1788544309	13.19 Volt	140 Pkt	76 Pcnt
1788542507	13.19 Volt	130 Pkt	77 Pcnt
1788540706	13.19 Volt	140 Pkt	83 Pcnt
1788538904	12.88 Volt	130 Pkt	80 Pcnt
1788537102	12.96 Volt	150 Pkt	79 Pcnt
1788535300	13.19 Volt	170 Pkt	79 Pcnt
1788533499	13.11 Volt	190 Pkt	78 Pcnt
1788531697	13.11 Volt	190 Pkt	82 Pcnt
1788529895	13.11 Volt	190 Pkt	84 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Value3: 0, 0, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)