NY0I-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object NY0I-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1788685924	14.25 Volt	1720 Pkt	70 Pcnt
1788685626	14.25 Volt	1720 Pkt	70 Pcnt
1788685624	14.25 Volt	1720 Pkt	70 Pcnt
1788685324	14.25 Volt	1700 Pkt	69 Pcnt
1788685025	14.25 Volt	1700 Pkt	70 Pcnt
1788685024	14.25 Volt	1700 Pkt	70 Pcnt
1788684724	14.25 Volt	1700 Pkt	70 Pcnt
1788684426	14.25 Volt	1730 Pkt	71 Pcnt
1788684424	14.25 Volt	1730 Pkt	71 Pcnt
1788684124	14.25 Volt	1700 Pkt	71 Pcnt
1788683825	14.25 Volt	1690 Pkt	71 Pcnt
1788683824	14.25 Volt	1690 Pkt	71 Pcnt
1788683524	14.25 Volt	1680 Pkt	70 Pcnt
1788683227	14.25 Volt	1690 Pkt	70 Pcnt
1788683224	14.25 Volt	1690 Pkt	70 Pcnt
1788682924	14.25 Volt	1690 Pkt	69 Pcnt
1788682624	14.25 Volt	1670 Pkt	69 Pcnt
1788682324	14.25 Volt	1690 Pkt	69 Pcnt
1788682026	14.25 Volt	1720 Pkt	69 Pcnt
1788682024	14.25 Volt	1720 Pkt	69 Pcnt
1788681724	14.25 Volt	1730 Pkt	70 Pcnt
1788681426	14.25 Volt	1720 Pkt	69 Pcnt
1788681424	14.25 Volt	1720 Pkt	69 Pcnt
1788681124	14.25 Volt	1730 Pkt	69 Pcnt
1788680825	14.25 Volt	1690 Pkt	68 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)