This is the latest recevied telemetry packets stored in our database for station/object ER-ECHO10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Value1*
Value2*
Value3*
Value4*
Value5*
1777064240
0 RX Erlang
0.96 TX Erlang
0 RXcount/10m
14 TXcount/10m
0 none1
1777063640
0 RX Erlang
0.96 TX Erlang
0 RXcount/10m
10 TXcount/10m
0 none1
1777063040
0 RX Erlang
0.91 TX Erlang
0 RXcount/10m
18 TXcount/10m
0 none1
1777062440
0 RX Erlang
0.91 TX Erlang
0 RXcount/10m
17 TXcount/10m
0 none1
1777061840
0 RX Erlang
0.96 TX Erlang
0 RXcount/10m
19 TXcount/10m
0 none1
1777061240
0 RX Erlang
0.94 TX Erlang
0 RXcount/10m
16 TXcount/10m
0 none1
1777060640
0 RX Erlang
0.84 TX Erlang
0 RXcount/10m
25 TXcount/10m
0 none1
1777060040
0 RX Erlang
0.32 TX Erlang
0 RXcount/10m
23 TXcount/10m
0 none1
1777059440
0 RX Erlang
0.39 TX Erlang
0 RXcount/10m
33 TXcount/10m
0 none1
1777058840
0 RX Erlang
0.68 TX Erlang
0 RXcount/10m
33 TXcount/10m
0 none1
1777058240
0 RX Erlang
0.88 TX Erlang
0 RXcount/10m
30 TXcount/10m
0 none1
1777057640
0 RX Erlang
0.81 TX Erlang
0 RXcount/10m
25 TXcount/10m
0 none1
*Used Equation Coefficients:
Value1: 0, 1, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)