N2RWE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N2RWE-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1789951742	12.4 Volt	160 Pkt	50 Pcnt
1789951442	12.56 Volt	160 Pkt	51 Pcnt
1789951142	12.48 Volt	170 Pkt	53 Pcnt
1789950842	12.48 Volt	180 Pkt	55 Pcnt
1789950542	11.22 Volt	190 Pkt	57 Pcnt
1789950242	13.04 Volt	190 Pkt	58 Pcnt
1789949942	12.48 Volt	190 Pkt	58 Pcnt
1789949642	12.48 Volt	200 Pkt	60 Pcnt
1789949342	12.25 Volt	200 Pkt	60 Pcnt
1789949042	12.32 Volt	200 Pkt	59 Pcnt
1789948742	12.32 Volt	200 Pkt	59 Pcnt
1789948442	12.48 Volt	200 Pkt	60 Pcnt
1789948142	11.85 Volt	210 Pkt	61 Pcnt
1789947842	11.85 Volt	220 Pkt	62 Pcnt
1789947542	13.67 Volt	220 Pkt	63 Pcnt
1789947244	13.75 Volt	230 Pkt	63 Pcnt
1789947242	13.75 Volt	230 Pkt	63 Pcnt
1789946942	13.67 Volt	210 Pkt	61 Pcnt
1789946642	13.98 Volt	210 Pkt	60 Pcnt
1789946342	13.98 Volt	210 Pkt	56 Pcnt
1789946042	13.98 Volt	200 Pkt	55 Pcnt
1789945742	13.9 Volt	190 Pkt	52 Pcnt
1789945445	13.98 Volt	230 Pkt	57 Pcnt
1789945442	13.98 Volt	230 Pkt	57 Pcnt
1789945142	13.98 Volt	270 Pkt	59 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)