YO3JAZ-NC Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3JAZ-NC. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Load*	RSSI*	Vcc*
1773101104	12 C	6.8 %	-63 dBm	3.44 V
1773100744	12 C	6.8 %	-63 dBm	3.44 V
1773100384	12 C	7.2 %	-62 dBm	3.44 V
1773100024	12 C	6.8 %	-63 dBm	3.43 V
1773099664	12 C	7.2 %	-62 dBm	3.44 V
1773099304	12 C	7.2 %	-63 dBm	3.44 V
1773098944	12 C	6.8 %	-63 dBm	3.44 V
1773098584	12 C	6.8 %	-63 dBm	3.43 V
1773098224	12 C	7.2 %	-63 dBm	3.44 V
1773097864	12 C	6.8 %	-63 dBm	3.44 V
1773097504	12 C	6.8 %	-63 dBm	3.44 V
1773097144	12 C	6.8 %	-63 dBm	3.44 V
1773096784	12 C	6.8 %	-63 dBm	3.43 V
1773096428	12 C	7.2 %	-63 dBm	3.43 V
1773096064	12 C	7.2 %	-63 dBm	3.44 V
1773095704	12 C	6.8 %	-64 dBm	3.44 V
1773095344	12.5 C	6.8 %	-63 dBm	3.44 V
1773094984	12 C	6.8 %	-62 dBm	3.44 V
1773094624	12 C	6.8 %	-61 dBm	3.44 V
1773094264	12 C	6.8 %	-61 dBm	3.44 V
1773093904	12.5 C	6.8 %	-62 dBm	3.43 V
1773093546	12 C	6.8 %	-63 dBm	3.43 V
1773093184	12.5 C	6.8 %	-61 dBm	3.44 V
1773092824	12.5 C	6.8 %	-62 dBm	3.44 V
1773092464	12.5 C	6.8 %	-62 dBm	3.44 V

*Used Equation Coefficients:

Temp: 0, 0.5, -25

Power: 0, 20, 0

Load: 0, 0.4, 0

RSSI: 0, -1, 0

Vcc: 0, 0.01, 2.5

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)