SQ9CH Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ9CH. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1772829654	12.45 Volt	220 Pkt	70 Pkt	60 Pcnt
1772822446	12.45 Volt	190 Pkt	100 Pkt	52 Pcnt
1772815239	12.45 Volt	310 Pkt	150 Pkt	61 Pcnt
1772808044	12.45 Volt	280 Pkt	130 Pkt	57 Pcnt
1772793619	12.45 Volt	230 Pkt	90 Pkt	58 Pcnt
1772786412	12.45 Volt	200 Pkt	80 Pkt	57 Pcnt
1772771999	12.45 Volt	160 Pkt	60 Pkt	51 Pcnt
1772764792	12.45 Volt	130 Pkt	50 Pkt	53 Pcnt
1772757585	12.45 Volt	140 Pkt	50 Pkt	61 Pcnt
1772750382	12.45 Volt	300 Pkt	70 Pkt	57 Pcnt
1772743172	12.45 Volt	220 Pkt	80 Pkt	65 Pcnt
1772735964	12.45 Volt	190 Pkt	90 Pkt	61 Pcnt
1772728760	12.45 Volt	300 Pkt	130 Pkt	68 Pcnt
1772721552	12.45 Volt	250 Pkt	140 Pkt	58 Pcnt
1772714344	12.45 Volt	150 Pkt	60 Pkt	62 Pcnt
1772707139	12.45 Volt	170 Pkt	80 Pkt	61 Pcnt
1772699930	12.45 Volt	190 Pkt	90 Pkt	65 Pcnt
1772692739	12.45 Volt	150 Pkt	50 Pkt	60 Pcnt
1772685517	12.45 Volt	150 Pkt	60 Pkt	50 Pcnt
1772678310	12.45 Volt	130 Pkt	50 Pkt	51 Pcnt
1772671103	12.45 Volt	140 Pkt	50 Pkt	52 Pcnt
1772663896	12.45 Volt	140 Pkt	50 Pkt	57 Pcnt
1772656689	12.45 Volt	180 Pkt	60 Pkt	56 Pcnt
1772649483	12.45 Volt	210 Pkt	90 Pkt	55 Pcnt
1772642276	12.45 Volt	290 Pkt	160 Pkt	64 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)