HB9FEF-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HB9FEF-8. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp 1*	Temp 2*
1784786751	12.83 Volt	15 C	15 C
1784784951	12.9 Volt	15 C	15 C
1784783151	12.9 Volt	15 C	15 C
1784781351	12.9 Volt	15 C	15 C
1784779551	12.9 Volt	15.5 C	15.5 C
1784777751	12.9 Volt	16 C	16 C
1784775951	12.9 Volt	16.5 C	16.5 C
1784774151	12.9 Volt	16.5 C	16.5 C
1784772351	12.9 Volt	17 C	17 C
1784770551	12.9 Volt	17.5 C	17.5 C
1784768751	12.98 Volt	17.5 C	17.5 C
1784766951	12.98 Volt	18 C	18 C
1784765151	12.98 Volt	18.5 C	18.5 C
1784763351	12.98 Volt	19 C	19 C
1784761551	12.98 Volt	19 C	19 C
1784759751	12.98 Volt	19.5 C	19.5 C
1784757951	13.05 Volt	20 C	20 C
1784756151	13.05 Volt	21 C	21 C
1784754351	13.05 Volt	22 C	22 C
1784752551	13.05 Volt	23 C	23 C
1784750752	13.05 Volt	24 C	24 C
1784748951	13.05 Volt	25 C	25 C
1784747151	13.13 Volt	26 C	26 C
1784745351	13.13 Volt	27 C	27 C
1784743551	13.13 Volt	27.5 C	27.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp 1: 0, 0.5, -64

Temp 2: 0, 0.5, -64

U: 0, 0.1, 0

I: 0, 19.5, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)