W9IZ-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W9IZ-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxPkHr*	DigPkHr*	DcEfHr*	DcEfTo*
1772690624	65 pkts	1 pkts	72 %	69 %
1772689724	69 pkts	1 pkts	74 %	69 %
1772688824	73 pkts	1 pkts	74 %	69 %
1772687925	74 pkts	1 pkts	73 %	69 %
1772687924	74 pkts	1 pkts	73 %	69 %
1772687024	75 pkts	1 pkts	74 %	69 %
1772686125	72 pkts	1 pkts	71 %	69 %
1772686124	72 pkts	1 pkts	71 %	69 %
1772685224	71 pkts	1 pkts	69 %	69 %
1772684326	71 pkts	1 pkts	70 %	69 %
1772684324	71 pkts	1 pkts	70 %	69 %
1772683424	74 pkts	1 pkts	71 %	69 %
1772682524	78 pkts	1 pkts	75 %	69 %
1772681625	77 pkts	1 pkts	76 %	69 %
1772680727	80 pkts	1 pkts	74 %	69 %
1772680725	80 pkts	1 pkts	74 %	69 %
1772679825	80 pkts	1 pkts	72 %	69 %
1772678925	80 pkts	1 pkts	69 %	69 %
1772678025	82 pkts	1 pkts	69 %	69 %
1772677125	79 pkts	1 pkts	70 %	69 %
1772677125	79 pkts	1 pkts	70 %	69 %
1772676225	77 pkts	1 pkts	73 %	69 %
1772675326	73 pkts	1 pkts	76 %	69 %
1772675325	73 pkts	1 pkts	76 %	69 %
1772674425	69 pkts	1 pkts	79 %	69 %

*Used Equation Coefficients:

RxPkHr: 0, 1, 0

DigPkHr: 0, 1, 0

DcEfHr: 0, 1, 0

DcEfTo: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)