This is the latest recevied telemetry packets stored in our database for station/object N2FSD-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Battery*
Charging/AC*
GPS+Sat*
A4*
A5*
1780336185
100 Percent
48 Charge/On/Off
78 Sats/On/Off
500 N/A
0 N/A
1780335285
100 Percent
48 Charge/On/Off
73 Sats/On/Off
500 N/A
0 N/A
1780334325
100 Percent
48 Charge/On/Off
78 Sats/On/Off
500 N/A
0 N/A
1780333425
100 Percent
48 Charge/On/Off
95 Sats/On/Off
500 N/A
0 N/A
1780331625
100 Percent
48 Charge/On/Off
93 Sats/On/Off
500 N/A
0 N/A
1780330725
100 Percent
48 Charge/On/Off
83 Sats/On/Off
500 N/A
0 N/A
1780329765
100 Percent
48 Charge/On/Off
88 Sats/On/Off
500 N/A
0 N/A
1780328865
100 Percent
48 Charge/On/Off
83 Sats/On/Off
500 N/A
0 N/A
1780327908
100 Percent
48 Charge/On/Off
88 Sats/On/Off
500 N/A
0 N/A
1780327006
100 Percent
48 Charge/On/Off
48 Sats/On/Off
500 N/A
0 N/A
1780238999
100 Percent
48 Charge/On/Off
83 Sats/On/Off
500 N/A
0 N/A
1780238099
100 Percent
48 Charge/On/Off
88 Sats/On/Off
500 N/A
0 N/A
1780237201
100 Percent
48 Charge/On/Off
95 Sats/On/Off
500 N/A
0 N/A
1780236299
100 Percent
48 Charge/On/Off
48 Sats/On/Off
500 N/A
0 N/A
*Used Equation Coefficients:
Battery: 0, 1, 0
Charging/AC: 0, 1, 0
GPS+Sat: 0, 1, 0
A4: 0, 1, 0
A5: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)