LZ2SMX-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LZ2SMX-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Tbsmt*	Rh*	Tfl1*	Tktcn*	Tloft*
1784688089	26 C	61 %	27 C	29 C	29 C
1784686889	26 C	61 %	27 C	29 C	29 C
1784685690	26 C	61 %	27 C	29 C	30 C
1784684491	26 C	61 %	27 C	29 C	30 C
1784682089	26 C	62 %	27 C	29 C	30 C
1784679690	26 C	62 %	27 C	29 C	30 C
1784676092	26 C	62 %	27 C	29 C	31 C
1784672490	26 C	62 %	27 C	29 C	32 C
1784659289	27 C	62 %	27 C	29 C	35 C
1784658089	27 C	62 %	27 C	29 C	35 C
1784656889	27 C	62 %	27 C	29 C	35 C
1784655689	27 C	62 %	27 C	29 C	36 C
1784654490	27 C	62 %	27 C	29 C	36 C
1784653288	27 C	62 %	27 C	29 C	36 C
1784652089	27 C	62 %	27 C	29 C	37 C
1784650889	27 C	63 %	27 C	29 C	37 C
1784649690	27 C	63 %	27 C	29 C	37 C
1784648489	27 C	63 %	27 C	29 C	37 C
1784647289	27 C	63 %	27 C	29 C	37 C
1784646089	27 C	63 %	27 C	29 C	37 C
1784644889	27 C	63 %	28 C	29 C	37 C
1784643688	27 C	63 %	27 C	29 C	37 C
1784642489	27 C	62 %	27 C	29 C	37 C
1784641289	26 C	62 %	28 C	29 C	37 C
1784640089	26 C	62 %	27 C	29 C	37 C

*Used Equation Coefficients:

Tbsmt: 0, 1, 0

Rh: 0, 1, 0

Tfl1: 0, 1, 0

Tktcn: 0, 1, 0

Tloft: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)