OK1JRA-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OK1JRA-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1754105016	227 Count	1 Count	4.03 VDC
1754103215	226 Count	1 Count	4 VDC
1754101414	225 Count	1 Count	4.02 VDC
1754099613	224 Count	1 Count	4.02 VDC
1754097813	223 Count	1 Count	4.05 VDC
1754094218	221 Count	1 Count	4.04 VDC
1754092418	220 Count	1 Count	4.03 VDC
1754090617	219 Count	1 Count	4 VDC
1754088816	218 Count	1 Count	4.04 VDC
1754087016	217 Count	1 Count	4.08 VDC
1754083414	215 Count	1 Count	4.01 VDC
1754079813	213 Count	1 Count	4 VDC
1754078012	212 Count	1 Count	4.06 VDC
1754076211	211 Count	1 Count	4.04 VDC
1754074410	210 Count	1 Count	4.1 VDC
1754072622	209 Count	1 Count	4.07 VDC
1754070818	208 Count	1 Count	4.09 VDC
1754069017	207 Count	1 Count	4.03 VDC
1754067217	206 Count	1 Count	4.03 VDC
1754065416	205 Count	1 Count	4.08 VDC
1754063615	204 Count	1 Count	4.06 VDC
1754060014	202 Count	1 Count	4.06 VDC
1754058213	201 Count	1 Count	4.06 VDC
1754056412	200 Count	1 Count	4.02 VDC
1754052811	198 Count	1 Count	4.01 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)