WA7DEM-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WA7DEM-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*
1765923038	12.72 Volts	64.81 Deg.F
1765915873	12.75 Volts	61.29 Deg.F
1765914082	12.72 Volts	61.29 Deg.F
1765906112	12.69 Volts	61.29 Deg.F
1765902808	12.69 Volts	62.17 Deg.F
1765901017	12.69 Volts	60.41 Deg.F
1765898485	12.69 Volts	61.29 Deg.F
1765896694	12.69 Volts	61.29 Deg.F
1765894903	12.72 Volts	62.17 Deg.F
1765893112	12.69 Volts	62.17 Deg.F
1765891320	12.69 Volts	62.17 Deg.F
1765887738	12.66 Volts	62.17 Deg.F
1765885947	12.69 Volts	63.05 Deg.F
1765884156	12.69 Volts	63.05 Deg.F
1765882365	12.72 Volts	63.05 Deg.F
1765880574	12.72 Volts	63.05 Deg.F
1765876992	12.75 Volts	63.93 Deg.F
1765873021	12.77 Volts	66.57 Deg.F
1765872952	12.75 Volts	65.69 Deg.F
1765872890	12.75 Volts	64.81 Deg.F
1765872671	12.75 Volts	64.81 Deg.F
1765871615	12.77 Volts	63.93 Deg.F
1765864449	12.98 Volts	65.69 Deg.F
1765858619	12.98 Volts	67.45 Deg.F
1765855036	12.57 Volts	67.45 Deg.F

*Used Equation Coefficients:

Value1: 0, 0.0293, 0

Value2: 0, 0.88, -459.67

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)