OE1XAR-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE1XAR-14. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1788566839	12.45 Volt	680 Pkt	77 Pcnt
1788566239	12.45 Volt	700 Pkt	77 Pcnt
1788565674	12.45 Volt	710 Pkt	78 Pcnt
1788565039	12.45 Volt	680 Pkt	78 Pcnt
1788564439	12.45 Volt	660 Pkt	78 Pcnt
1788563839	12.45 Volt	650 Pkt	77 Pcnt
1788563239	12.45 Volt	580 Pkt	75 Pcnt
1788562639	12.45 Volt	560 Pkt	74 Pcnt
1788562039	12.45 Volt	530 Pkt	73 Pcnt
1788561439	12.45 Volt	510 Pkt	71 Pcnt
1788560839	12.45 Volt	510 Pkt	71 Pcnt
1788560263	12.45 Volt	510 Pkt	72 Pcnt
1788559639	12.45 Volt	510 Pkt	71 Pcnt
1788559039	12.45 Volt	520 Pkt	70 Pcnt
1788558442	12.45 Volt	530 Pkt	70 Pcnt
1788557839	12.45 Volt	540 Pkt	69 Pcnt
1788557239	12.45 Volt	550 Pkt	68 Pcnt
1788556639	12.45 Volt	550 Pkt	68 Pcnt
1788556039	12.45 Volt	560 Pkt	67 Pcnt
1788555439	12.45 Volt	580 Pkt	67 Pcnt
1788554844	12.45 Volt	600 Pkt	69 Pcnt
1788554239	12.45 Volt	600 Pkt	69 Pcnt
1788553639	12.45 Volt	580 Pkt	68 Pcnt
1788553062	12.45 Volt	600 Pkt	69 Pcnt
1788552440	12.45 Volt	580 Pkt	69 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)