VK5RLD-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK5RLD-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1788601711	12.9 Volt	92 Pcnt	12.5 C
1788600811	12.98 Volt	93 Pcnt	13 C
1788599910	12.98 Volt	94 Pcnt	13.5 C
1788599009	12.98 Volt	94 Pcnt	13.5 C
1788598108	12.98 Volt	94 Pcnt	14.5 C
1788597207	12.98 Volt	95 Pcnt	15 C
1788596320	12.9 Volt	97 Pcnt	15.5 C
1788595405	14.03 Volt	95 Pcnt	16 C
1788594505	14.18 Volt	93 Pcnt	16 C
1788593604	14.7 Volt	91 Pcnt	16 C
1788592703	14.1 Volt	90 Pcnt	16.5 C
1788591802	14.1 Volt	93 Pcnt	17 C
1788590901	14.1 Volt	96 Pcnt	18.5 C
1788590000	14.1 Volt	96 Pcnt	19 C
1788589099	14.1 Volt	94 Pcnt	18 C
1788588198	14.1 Volt	95 Pcnt	19.5 C
1788587298	14.1 Volt	93 Pcnt	19.5 C
1788586397	14.1 Volt	96 Pcnt	20 C
1788585496	14.1 Volt	92 Pcnt	19.5 C
1788584595	14.03 Volt	86 Pcnt	19.5 C
1788583709	14.1 Volt	86 Pcnt	20 C
1788582793	14.1 Volt	86 Pcnt	19 C
1788581892	14.03 Volt	88 Pcnt	19.5 C
1788580992	14.03 Volt	87 Pcnt	18.5 C
1788580091	14.1 Volt	86 Pcnt	19.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

U1: 0, 0.1, 0

U2: 0, 0.1, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)