WM6Y-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WM6Y-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RFIn*	RFiGate*	Temp*
1776948568	194 Pkts	186 Pkts	32 C
1776944968	180 Pkts	177 Pkts	32 C
1776941368	182 Pkts	179 Pkts	32 C
1776937768	173 Pkts	169 Pkts	33 C
1776934168	156 Pkts	151 Pkts	34 C
1776930568	146 Pkts	141 Pkts	34 C
1776926968	144 Pkts	140 Pkts	34 C
1776923368	189 Pkts	184 Pkts	34 C
1776919768	198 Pkts	188 Pkts	35 C
1776916168	214 Pkts	206 Pkts	34 C
1776912568	213 Pkts	206 Pkts	35 C
1776908968	235 Pkts	228 Pkts	35 C
1776905368	191 Pkts	181 Pkts	35 C
1776901768	205 Pkts	197 Pkts	34 C
1776898168	156 Pkts	149 Pkts	34 C
1776894568	110 Pkts	101 Pkts	34 C
1776890968	110 Pkts	102 Pkts	34 C
1776887368	129 Pkts	116 Pkts	34 C
1776883768	108 Pkts	100 Pkts	34 C
1776880168	132 Pkts	123 Pkts	34 C
1776876568	103 Pkts	97 Pkts	34 C
1776872968	110 Pkts	103 Pkts	34 C
1776869368	144 Pkts	134 Pkts	33 C
1776865768	149 Pkts	141 Pkts	34 C
1776862168	170 Pkts	159 Pkts	34 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)