DG6DXG-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG6DXG-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1757406940	20.8 C	37.71 %	1019.5 hPa
1757406035	20.6 C	37.72 %	1020 hPa
1757402415	20.1 C	37.41 %	1018.88 hPa
1757401509	19.9 C	37.46 %	1018.5 hPa
1757396080	19.6 C	36.87 %	1018.63 hPa
1757387935	19.9 C	36.92 %	1018.38 hPa
1757387030	20 C	37.18 %	1016.25 hPa
1757386125	20 C	36.97 %	1019 hPa
1757385220	20 C	36.78 %	1018.5 hPa
1757384314	20.1 C	36.84 %	1018.38 hPa
1757383410	20.2 C	36.79 %	1020.63 hPa
1757380695	20.6 C	36.2 %	1019.63 hPa
1757379790	20.8 C	36.55 %	1020.5 hPa
1757377980	21.2 C	36.36 %	1018.63 hPa
1757377075	21.3 C	36.54 %	1019.63 hPa
1757376170	21.4 C	36.62 %	1020.75 hPa
1757375265	21.6 C	36.66 %	1020.5 hPa
1757374360	21.7 C	36.94 %	1021.88 hPa
1757373455	21.9 C	36.89 %	1022 hPa
1757372550	22 C	36.8 %	1022.13 hPa
1757371645	22.1 C	36.74 %	1022.25 hPa
1757370739	22.3 C	36.45 %	1022.88 hPa
1757369835	22.5 C	36.85 %	1022.75 hPa
1757368930	22.7 C	36.72 %	1024 hPa
1757368034	22.9 C	37.02 %	1023.25 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)