LD4AI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LD4AI. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1784719400	12.6 Volt	360 Pkt	68 Pcnt	24.5 C
1784719100	12.6 Volt	380 Pkt	67 Pcnt	24.5 C
1784718802	12.6 Volt	390 Pkt	66 Pcnt	24.5 C
1784718800	12.6 Volt	390 Pkt	66 Pcnt	24.5 C
1784718500	12.6 Volt	390 Pkt	66 Pcnt	24.5 C
1784718199	12.6 Volt	380 Pkt	65 Pcnt	24.5 C
1784717899	12.6 Volt	380 Pkt	65 Pcnt	24.5 C
1784717599	12.6 Volt	390 Pkt	64 Pcnt	24.5 C
1784717299	12.6 Volt	400 Pkt	62 Pcnt	24.5 C
1784716998	12.6 Volt	430 Pkt	61 Pcnt	24.5 C
1784716698	12.6 Volt	440 Pkt	60 Pcnt	24.5 C
1784716398	12.6 Volt	460 Pkt	59 Pcnt	24.5 C
1784716097	12.6 Volt	480 Pkt	60 Pcnt	24.5 C
1784715797	12.6 Volt	490 Pkt	60 Pcnt	24.5 C
1784715497	12.6 Volt	480 Pkt	60 Pcnt	24.5 C
1784715196	12.6 Volt	480 Pkt	60 Pcnt	24.5 C
1784714896	12.6 Volt	490 Pkt	62 Pcnt	24.5 C
1784714598	12.6 Volt	490 Pkt	62 Pcnt	24.5 C
1784714596	12.6 Volt	490 Pkt	62 Pcnt	24.5 C
1784714296	12.6 Volt	480 Pkt	62 Pcnt	24.5 C
1784713995	12.6 Volt	480 Pkt	63 Pcnt	24.5 C
1784713695	12.6 Volt	470 Pkt	63 Pcnt	24.5 C
1784713397	12.6 Volt	470 Pkt	62 Pcnt	24.5 C
1784713395	12.6 Volt	470 Pkt	62 Pcnt	24.5 C
1784713094	12.6 Volt	470 Pkt	64 Pcnt	24.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)