TA8TL-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA8TL-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1773254062	12.23 Volt	20 Pkt	83 Pcnt
1773253462	12.23 Volt	40 Pkt	83 Pcnt
1773252862	12.23 Volt	20 Pkt	82 Pcnt
1773251662	12.23 Volt	30 Pkt	80 Pcnt
1773251063	12.23 Volt	40 Pkt	79 Pcnt
1773250463	12.23 Volt	20 Pkt	78 Pcnt
1773249863	12.23 Volt	30 Pkt	77 Pcnt
1773249263	12.23 Volt	30 Pkt	76 Pcnt
1773248663	12.23 Volt	40 Pkt	76 Pcnt
1773244466	12.23 Volt	30 Pkt	82 Pcnt
1773243863	12.23 Volt	30 Pkt	81 Pcnt
1773242063	12.23 Volt	10 Pkt	76 Pcnt
1773240867	12.23 Volt	20 Pkt	75 Pcnt
1773240263	12.23 Volt	20 Pkt	73 Pcnt
1773237263	12.23 Volt	20 Pkt	80 Pcnt
1773236663	12.23 Volt	20 Pkt	75 Pcnt
1773236063	12.23 Volt	30 Pkt	75 Pcnt
1773210264	12.23 Volt	30 Pkt	92 Pcnt
1773208464	12.23 Volt	10 Pkt	100 Pcnt
1773206064	12.23 Volt	0 Pkt	100 Pcnt
1773204864	12.23 Volt	20 Pkt	100 Pcnt
1773204264	12.23 Volt	10 Pkt	100 Pcnt
1773201264	12.23 Volt	10 Pkt	100 Pcnt
1773200664	12.23 Volt	30 Pkt	100 Pcnt
1773200068	12.23 Volt	20 Pkt	100 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)