VE3STP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE3STP-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Shack Temp*	CPU Temp*	CPU Usage*
1784710493	13.3 V	25.9 C	46.8 C	0 %
1784708693	13.3 V	26.3 C	47.1 C	1 %
1784706894	13.2 V	26.5 C	47.1 C	1 %
1784705092	13.2 V	26.6 C	47.5 C	1 %
1784703292	13.2 V	26.6 C	47.6 C	1 %
1784701493	13.2 V	26.7 C	47.6 C	1 %
1784699692	13.2 V	26.8 C	47.5 C	1 %
1784697893	13.3 V	26.8 C	47.7 C	1 %
1784696093	13.2 V	26.9 C	47.7 C	1 %
1784694292	13.3 V	26.9 C	47.9 C	1 %
1784692492	13.1 V	26.9 C	48.1 C	1 %
1784690691	13.2 V	26.9 C	47.9 C	1 %
1784688891	13.3 V	27 C	47.9 C	1 %
1784687091	13.3 V	27.1 C	48.1 C	1 %
1784685292	13.3 V	27.1 C	48.2 C	2 %
1784683490	13.2 V	27 C	48.1 C	2 %
1784681690	13.2 V	26.5 C	48.1 C	2 %
1784679890	13.3 V	25.5 C	45.4 C	2 %
1784678090	13.2 V	26 C	43 C	2 %
1784676290	13.1 V	26.2 C	43.3 C	2 %
1784674490	13.3 V	27 C	44 C	2 %
1784672689	13.2 V	27.8 C	48.5 C	3 %
1784670888	13.3 V	27.5 C	48.4 C	2 %
1784669088	13.3 V	27.2 C	48.4 C	2 %
1784667289	13.2 V	26.9 C	47.9 C	1 %

*Used Equation Coefficients:

Battery: 0, 0.1, 0

Shack Temp: 0, 0.1, 0

CPU Temp: 0, 0.1, 0

CPU Usage: 0, 1, 0

Fan Speed: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)