DC5WT-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DC5WT-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1772625503	15.9 deg C	53.4 %	1026.9 hPa
1772624615	16.3 deg C	53.4 %	1027 hPa
1772623703	16.5 deg C	52.6 %	1027.2 hPa
1772622803	16.1 deg C	53.8 %	1027.3 hPa
1772621903	16.5 deg C	52.2 %	1027.3 hPa
1772621025	15.8 deg C	55.7 %	1027.5 hPa
1772620103	15.4 deg C	57 %	1027.6 hPa
1772619202	16.3 deg C	56.9 %	1027.6 hPa
1772618302	15.4 deg C	56.9 %	1027.7 hPa
1772617402	16.1 deg C	58.5 %	1027.6 hPa
1772616502	13.8 deg C	62.3 %	1027.9 hPa
1772615610	13 deg C	62 %	1028 hPa
1772614702	12.6 deg C	63.7 %	1028.1 hPa
1772613802	11.4 deg C	67.5 %	1028.3 hPa
1772613472	10.2 deg C	69.3 %	1028.4 hPa
1772612572	9.5 deg C	70.4 %	1028.5 hPa
1772611672	8.4 deg C	73 %	1028.8 hPa
1772610772	9.2 deg C	72.6 %	1028.6 hPa
1772609872	3.5 deg C	78.6 %	1029.4 hPa
1772608972	2.5 deg C	78.8 %	1029.5 hPa
1772608072	2 deg C	78.7 %	1029.4 hPa
1772607172	1.6 deg C	79 %	1029.5 hPa
1772606272	1.1 deg C	78.8 %	1029.4 hPa
1772605372	0.7 deg C	79.2 %	1029.3 hPa
1772604471	0.6 deg C	78.9 %	1029.2 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)