W8MHS-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W8MHS-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Alt*	Temp*	RH*	Batt*
1777566133	620 ft	72.32 F	35 %	8.53 V
1777566013	597 ft	72.14 F	35 %	8.54 V
1777565893	607 ft	72.32 F	35 %	8.54 V
1777565774	617 ft	72.14 F	35 %	8.58 V
1777565654	650 ft	72.14 F	35 %	8.56 V
1777565533	637 ft	71.96 F	36 %	8.57 V
1777565415	623 ft	71.96 F	36 %	8.54 V
1777565293	597 ft	71.96 F	36 %	8.59 V
1777565173	600 ft	71.78 F	36 %	8.6 V
1777565053	610 ft	71.78 F	36 %	8.64 V
1777564933	633 ft	71.78 F	36 %	8.64 V
1777564813	623 ft	71.6 F	36 %	8.73 V
1777564693	620 ft	71.6 F	36 %	8.83 V
1777476610	659 ft	72.14 F	37 %	8.8 V
1777476492	597 ft	72.14 F	37 %	8.84 V
1777476371	610 ft	72.14 F	36 %	8.83 V
1777476249	577 ft	72.14 F	36 %	8.84 V
1777476131	587 ft	72.14 F	36 %	8.9 V
1777475747	653 ft	72.14 F	36 %	9.02 V
1777475627	594 ft	72.14 F	36 %	9.05 V
1777475507	561 ft	72.32 F	36 %	9.08 V
1777475387	548 ft	72.32 F	36 %	9.13 V
1777475266	558 ft	72.32 F	36 %	9.17 V
1777475146	571 ft	72.32 F	36 %	9.24 V
1777394492	597 ft	74.84 F	35 %	8.51 V

*Used Equation Coefficients:

Alt: 0, 1, 0

Temp: 0, 0.18, 32

RH: 0, 1, 0

Spd: 0, 0.62137, 0

Batt: 0, 0.01, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)