SK3JR-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SK3JR-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Bat*	Chg*	Temp*
1773216175	14.03 Volt	13.8 Volt	0.59 A	2.5 C
1773214976	13.8 Volt	13.5 Volt	0.2 A	1.5 C
1773213775	13.8 Volt	13.5 Volt	0.2 A	1.5 C
1773212576	13.8 Volt	13.5 Volt	0 A	1 C
1773211376	13.8 Volt	13.5 Volt	0 A	0 C
1773210176	13.8 Volt	13.5 Volt	0 A	0 C
1773208976	13.8 Volt	13.5 Volt	0 A	0 C
1773207776	13.8 Volt	13.5 Volt	0 A	0 C
1773206576	13.8 Volt	13.5 Volt	0 A	0 C
1773205376	13.8 Volt	13.5 Volt	0 A	0 C
1773204176	13.8 Volt	13.5 Volt	0 A	0 C
1773202976	13.8 Volt	13.5 Volt	0 A	0 C
1773201776	13.8 Volt	13.5 Volt	0 A	-0.5 C
1773200576	13.8 Volt	13.5 Volt	0 A	-0.5 C
1773199376	13.8 Volt	13.5 Volt	0 A	-0.5 C
1773198176	13.8 Volt	13.5 Volt	0 A	0 C
1773196976	13.8 Volt	13.5 Volt	0 A	0 C
1773195776	13.8 Volt	13.5 Volt	0 A	0.5 C
1773194576	13.8 Volt	13.5 Volt	0 A	1 C
1773193376	13.8 Volt	13.5 Volt	0 A	1 C
1773192176	13.8 Volt	13.5 Volt	0 A	1 C
1773190977	13.8 Volt	13.5 Volt	0 A	1.5 C
1773189777	13.8 Volt	13.5 Volt	0 A	2 C
1773188577	13.8 Volt	13.5 Volt	0 A	2 C
1773187377	13.8 Volt	13.5 Volt	0 A	2.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Bat: 0, 0.1, 0

Wind: 0, 0.3, 0

Chg: 0, 0.1953, -24.8031

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)