This is the latest recevied telemetry packets stored in our database for station/object OE6POD-8. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Press*
Temp.in*
Hum*
QNH*
Temp.out*
1785230906
945.3 hPa
16.9 C deg
39.3 %
1030.3 hPa
22.2 C deg
1785208961
945.5 hPa
11.6 C deg
36.3 %
1033.2 hPa
21 C deg
1785138509
935.8 hPa
11.5 C deg
30.4 %
1023.8 hPa
19.5 C deg
1784962252
917.2 hPa
19.4 C deg
23.6 %
1153.9 hPa
17.6 C deg
1784960764
812.1 hPa
18 C deg
23.2 %
1022.9 hPa
17.3 C deg
1784960575
812.3 hPa
17.3 C deg
24 %
1023.6 hPa
17.2 C deg
1784960487
812.3 hPa
17.3 C deg
24 %
1023.6 hPa
17.2 C deg
1784955347
819.3 hPa
18.5 C deg
21 %
892.6 hPa
17.4 C deg
1784953534
925.6 hPa
10.7 C deg
22.9 %
1010.7 hPa
14 C deg
1784872896
940.1 hPa
4.2 C deg
32.4 %
1029.1 hPa
14.2 C deg
1784777493
0 hPa
0 C deg
0 %
0 hPa
21.4 C deg
1784604565
943.1 hPa
11.3 C deg
43.7 %
1026.6 hPa
22.5 C deg
1784562085
940.6 hPa
20.3 C deg
40.9 %
1027.4 hPa
26.1 C deg
*Used Equation Coefficients:
Press: 0, 1, 0
Temp.in: 0, 1, 0
Hum: 0, 1, 0
QNH: 0, 1, 0
Temp.out: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)