YO3JAZ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3JAZ-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V_Ext*	Value2*	Value3*	Value4*	Value5*
1765523223	12.9 VDC	0	0	0	0
1765522023	13 VDC	0	0	0	0
1765520823	13 VDC	0	0	0	0
1765519623	13.02 VDC	0	0	0	0
1765518423	12.96 VDC	0	0	0	0
1765517223	11.8 VDC	0	0	0	0
1765516023	11.84 VDC	0	0	0	0
1765514823	11.94 VDC	0	0	0	0
1765513623	11.86 VDC	0	0	0	0
1765512423	11.82 VDC	0	0	0	0
1765511223	11.84 VDC	0	0	0	0
1765510023	11.74 VDC	0	0	0	0
1765508823	11.78 VDC	0	0	0	0
1765507623	11.66 VDC	0	0	0	0
1765506423	11.62 VDC	0	0	0	0
1765505223	11.78 VDC	0	0	0	0
1765504023	10.92 VDC	0	0	0	0
1765502821	11.16 VDC	0	0	0	0
1765501623	11.24 VDC	0	0	0	0
1765500435	11.42 VDC	0	0	0	0
1765499223	11.66 VDC	0	0	0	0
1765498023	11.56 VDC	0	0	0	0
1765496823	11.5 VDC	0	0	0	0
1765495623	11.56 VDC	0	0	0	0
1765494423	11.6 VDC	0	0	0	0

*Used Equation Coefficients:

V_Ext: 0, 0.02, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)