DB0WBD-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0WBD-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1776682664	14.14 Volt	250 Pkt	10 Pkt	47 Pcnt
1776679060	14.14 Volt	230 Pkt	0 Pkt	49 Pcnt
1776675457	14.14 Volt	250 Pkt	10 Pkt	52 Pcnt
1776671854	14.14 Volt	230 Pkt	10 Pkt	52 Pcnt
1776668250	14.14 Volt	220 Pkt	10 Pkt	53 Pcnt
1776664647	14.14 Volt	270 Pkt	10 Pkt	58 Pcnt
1776661044	14.14 Volt	310 Pkt	10 Pkt	61 Pcnt
1776657439	14.14 Volt	250 Pkt	10 Pkt	57 Pcnt
1776653836	14.14 Volt	250 Pkt	10 Pkt	65 Pcnt
1776650233	14.14 Volt	190 Pkt	0 Pkt	56 Pcnt
1776646629	14.14 Volt	200 Pkt	10 Pkt	54 Pcnt
1776643026	14.14 Volt	220 Pkt	10 Pkt	58 Pcnt
1776639422	14.14 Volt	230 Pkt	10 Pkt	54 Pcnt
1776635819	14.14 Volt	250 Pkt	10 Pkt	54 Pcnt
1776632215	14.14 Volt	300 Pkt	20 Pkt	57 Pcnt
1776628614	14.14 Volt	290 Pkt	10 Pkt	56 Pcnt
1776625008	14.14 Volt	350 Pkt	20 Pkt	55 Pcnt
1776621405	14.14 Volt	350 Pkt	10 Pkt	56 Pcnt
1776617801	14.14 Volt	400 Pkt	20 Pkt	54 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)