TK5EP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TK5EP-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vbat*	Temp*	Hum*
1785280740	3.6 Volt	20.5 degC	64.5 %
1785280108	3.6 Volt	20.5 degC	64.5 %
1785278842	3.6 Volt	20.5 degC	64.5 %
1785278210	3.6 Volt	20.5 degC	64 %
1785277578	3.6 Volt	21 degC	64 %
1785276311	3.6 Volt	21 degC	63.5 %
1785275678	3.61 Volt	21 degC	63.5 %
1785273781	3.61 Volt	21.5 degC	63 %
1785273148	3.61 Volt	21.5 degC	63 %
1785272515	3.61 Volt	22 degC	63 %
1785271247	3.61 Volt	22 degC	62.5 %
1785270613	3.63 Volt	22.5 degC	62.5 %
1785269980	3.63 Volt	23 degC	62 %
1785268712	3.63 Volt	23 degC	62.5 %
1785268079	3.63 Volt	23.5 degC	62 %
1785267445	3.63 Volt	23.5 degC	62 %
1785266178	3.64 Volt	24.5 degC	61.5 %
1785265544	3.64 Volt	25 degC	61.5 %
1785264910	3.64 Volt	25.5 degC	61 %
1785263027	3.64 Volt	27 degC	61 %
1785262368	3.64 Volt	27.5 degC	60.5 %
1785260460	3.65 Volt	28.5 degC	60 %
1785259825	3.65 Volt	28.5 degC	60 %
1785257916	3.65 Volt	30 degC	59.5 %
1785257280	3.65 Volt	30.5 degC	59.5 %

*Used Equation Coefficients:

Vbat: 0, 0.008, 2.5

Temp: 0, 0.5, -40

Hum: 0, 0.5, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)