DL9DMN-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL9DMN-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1787583928	13.88 Volt	170 Pkt	79 Pcnt
1787583628	13.95 Volt	180 Pkt	79 Pcnt
1787583328	13.95 Volt	180 Pkt	78 Pcnt
1787583028	13.95 Volt	190 Pkt	79 Pcnt
1787582728	13.88 Volt	180 Pkt	79 Pcnt
1787582428	13.88 Volt	190 Pkt	81 Pcnt
1787582128	13.88 Volt	190 Pkt	80 Pcnt
1787581828	13.95 Volt	180 Pkt	81 Pcnt
1787581528	13.88 Volt	190 Pkt	81 Pcnt
1787581228	13.88 Volt	180 Pkt	80 Pcnt
1787580928	13.88 Volt	180 Pkt	80 Pcnt
1787580628	13.88 Volt	190 Pkt	77 Pcnt
1787580328	13.95 Volt	190 Pkt	75 Pcnt
1787580028	13.95 Volt	190 Pkt	76 Pcnt
1787579728	13.95 Volt	190 Pkt	75 Pcnt
1787579428	13.95 Volt	190 Pkt	75 Pcnt
1787579128	13.95 Volt	180 Pkt	76 Pcnt
1787578828	13.88 Volt	190 Pkt	77 Pcnt
1787578528	13.95 Volt	190 Pkt	77 Pcnt
1787578228	13.95 Volt	190 Pkt	78 Pcnt
1787577928	13.95 Volt	190 Pkt	78 Pcnt
1787577629	13.95 Volt	190 Pkt	79 Pcnt
1787577328	13.88 Volt	180 Pkt	81 Pcnt
1787577029	13.95 Volt	180 Pkt	82 Pcnt
1787576728	13.95 Volt	170 Pkt	85 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)