VA3APW-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VA3APW-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1787562551	13.13 Volt	150 Pkt	29 Pcnt
1787562251	13.13 Volt	150 Pkt	29 Pcnt
1787561950	13.13 Volt	160 Pkt	30 Pcnt
1787561651	13.13 Volt	140 Pkt	29 Pcnt
1787561351	13.13 Volt	150 Pkt	31 Pcnt
1787561051	13.13 Volt	160 Pkt	32 Pcnt
1787560751	13.13 Volt	140 Pkt	32 Pcnt
1787560451	13.13 Volt	130 Pkt	31 Pcnt
1787560151	13.13 Volt	120 Pkt	30 Pcnt
1787559851	13.13 Volt	110 Pkt	28 Pcnt
1787559551	13.13 Volt	110 Pkt	31 Pcnt
1787559251	13.13 Volt	110 Pkt	30 Pcnt
1787558951	13.13 Volt	110 Pkt	30 Pcnt
1787558651	13.13 Volt	110 Pkt	32 Pcnt
1787558351	13.13 Volt	110 Pkt	31 Pcnt
1787558051	13.13 Volt	100 Pkt	30 Pcnt
1787557751	13.13 Volt	90 Pkt	29 Pcnt
1787557451	13.13 Volt	80 Pkt	28 Pcnt
1787557151	13.13 Volt	80 Pkt	26 Pcnt
1787556851	13.13 Volt	90 Pkt	27 Pcnt
1787556551	13.13 Volt	90 Pkt	29 Pcnt
1787556251	13.13 Volt	80 Pkt	27 Pcnt
1787555951	13.13 Volt	90 Pkt	29 Pcnt
1787555651	13.13 Volt	90 Pkt	28 Pcnt
1787555351	13.13 Volt	90 Pkt	25 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Rx10m: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)