SR6WXP Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR6WXP. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*	Tempre*
1784692751	3 Pkt	6 Pkt	0 Pkt	30 DegC
1784691547	1 Pkt	3 Pkt	0 Pkt	30 DegC
1784690944	4 Pkt	2 Pkt	0 Pkt	30 DegC
1784690344	4 Pkt	7 Pkt	0 Pkt	30 DegC
1784689133	4 Pkt	5 Pkt	1 Pkt	30 DegC
1784688530	4 Pkt	3 Pkt	1 Pkt	30 DegC
1784687930	3 Pkt	4 Pkt	0 Pkt	30 DegC
1784687326	3 Pkt	3 Pkt	1 Pkt	30 DegC
1784686726	4 Pkt	3 Pkt	0 Pkt	30.5 DegC
1784686124	3 Pkt	3 Pkt	0 Pkt	30.5 DegC
1784685523	3 Pkt	3 Pkt	0 Pkt	30.5 DegC
1784684921	2 Pkt	2 Pkt	0 Pkt	30.5 DegC
1784684321	3 Pkt	7 Pkt	1 Pkt	30.5 DegC
1784683719	0 Pkt	5 Pkt	0 Pkt	30.5 DegC
1784683116	0 Pkt	6 Pkt	0 Pkt	30.5 DegC
1784682515	1 Pkt	2 Pkt	0 Pkt	30.5 DegC
1784681915	1 Pkt	4 Pkt	0 Pkt	30.5 DegC
1784681313	2 Pkt	5 Pkt	0 Pkt	30.5 DegC
1784680706	0 Pkt	6 Pkt	0 Pkt	30.5 DegC
1784680100	0 Pkt	2 Pkt	0 Pkt	31 DegC
1784679500	0 Pkt	4 Pkt	0 Pkt	31 DegC
1784678896	0 Pkt	2 Pkt	0 Pkt	31 DegC
1784678296	1 Pkt	3 Pkt	0 Pkt	31 DegC
1784677694	0 Pkt	3 Pkt	0 Pkt	31 DegC
1784677094	0 Pkt	3 Pkt	0 Pkt	31 DegC

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)