UR4SWG-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object UR4SWG-14. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1781415077	12.3 Volt	160 Pkt	140 Pkt	97 Pcnt
1781414777	12.45 Volt	160 Pkt	150 Pkt	97 Pcnt
1781414477	12.38 Volt	160 Pkt	140 Pkt	97 Pcnt
1781414177	12.38 Volt	160 Pkt	140 Pkt	98 Pcnt
1781413877	12.3 Volt	160 Pkt	150 Pkt	98 Pcnt
1781413577	12.45 Volt	160 Pkt	140 Pkt	97 Pcnt
1781413277	12.45 Volt	170 Pkt	150 Pkt	97 Pcnt
1781412977	12.45 Volt	160 Pkt	150 Pkt	97 Pcnt
1781412677	12.45 Volt	170 Pkt	150 Pkt	97 Pcnt
1781412377	12.45 Volt	170 Pkt	140 Pkt	96 Pcnt
1781412078	12.3 Volt	170 Pkt	150 Pkt	96 Pcnt
1781411777	12.45 Volt	170 Pkt	150 Pkt	97 Pcnt
1781411478	12.45 Volt	180 Pkt	150 Pkt	98 Pcnt
1781411177	12.45 Volt	180 Pkt	140 Pkt	98 Pcnt
1781410878	12.45 Volt	180 Pkt	140 Pkt	98 Pcnt
1781410578	12.38 Volt	180 Pkt	140 Pkt	98 Pcnt
1781410278	12.45 Volt	180 Pkt	140 Pkt	98 Pcnt
1781409978	12.45 Volt	180 Pkt	140 Pkt	98 Pcnt
1781409678	12.3 Volt	170 Pkt	140 Pkt	99 Pcnt
1781409379	12.45 Volt	170 Pkt	140 Pkt	98 Pcnt
1781409378	12.45 Volt	170 Pkt	140 Pkt	98 Pcnt
1781409078	12.45 Volt	170 Pkt	130 Pkt	99 Pcnt
1781408778	12.45 Volt	170 Pkt	140 Pkt	98 Pcnt
1781408478	12.3 Volt	170 Pkt	130 Pkt	98 Pcnt
1781408181	12.38 Volt	170 Pkt	140 Pkt	96 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)