LZ1NAG-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LZ1NAG-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1788512524	41.1 C	21.49 %	1018.5 hPa
1788511967	40.2 C	22.76 %	1020.13 hPa
1788511501	39.1 C	24.53 %	1020.5 hPa
1788510906	37.6 C	25.44 %	1021.5 hPa
1788510554	36.8 C	26.81 %	1024.38 hPa
1788502248	34.9 C	29.97 %	1024.63 hPa
1788501927	32.5 C	29.65 %	1021.38 hPa
1788498686	28.3 C	37.46 %	1025.25 hPa
1788498484	30.2 C	37.28 %	1024.13 hPa
1788498327	29.2 C	37.82 %	1023.25 hPa
1788498151	26.4 C	40.47 %	1023.5 hPa
1788497946	27.9 C	40.56 %	1024.13 hPa
1788497719	27.8 C	41.94 %	1020.38 hPa
1788497508	28.3 C	37.52 %	1025.88 hPa
1788497385	28.8 C	34.65 %	1025.88 hPa
1788497253	28.7 C	33.16 %	1026 hPa
1788496314	21.2 C	39.66 %	1026.5 hPa
1788435673	35.6 C	34.99 %	1023.75 hPa
1788431044	34.4 C	29.72 %	1025.63 hPa
1788426526	34.5 C	34.71 %	1025.25 hPa
1788424230	34.5 C	27.45 %	1027.25 hPa
1788424064	32.5 C	27.24 %	1025.75 hPa
1788421319	28.4 C	30.58 %	1025.25 hPa
1788421021	27.5 C	33.14 %	1025.88 hPa
1788418919	28.1 C	30.45 %	1026.88 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)